Bathroom Taps & Basin Mixers

4 designs · each in 6 finishes
  • Antique Brass

    Wall spout & mixer set

    Milano Wall Spout Plus Wall Mixer

    Spout 192 mm · Valve depth 45–70 mm

    $389

    Other finishes from $209

  • Antique Brass

    Tall basin mixer

    Vienna Tall Basin Mixer

    5.0 (2) average rating

    Height 305 mm · Reach 180 mm

    $409

    Other finishes from $249

  • Antique Brass

    Wall mixer

    Milano Wall Mixer

    4.3 (3) average rating

    Plate Ø65 mm · Valve depth 45–70 mm

    $279

    Other finishes from $149

  • Antique Brass

    Short basin mixer

    Vienna Short Basin Mixer

    4.3 (3) average rating

    Height 175 mm · Reach 140 mm

    $329

    Other finishes from $239

COMPARE THE MIXERS

How to choose a bathroom tap

The basin decides most of it. Here is how the four designs differ.

Vienna Short: set-in basins

175 mm tall with 75 mm under the spout and a 140 mm reach. For basins set into the bench or only slightly raised.

Vienna Tall: above-bench basins

305 mm tall with 200 mm under the spout and a 180 mm reach. For vessel basins with a rim up to about 150 mm.

Milano: wall mixer or set

Keeps the bench clear and suits any basin. The in-wall body needs 45 to 70 mm of depth and goes in before the wall is lined. The spout projects 192 mm.

The 50 mm rule

Leave at least 50 mm between the basin rim and the underside of the spout. Which tap fits my basin?

Basin and wall mixer questions

What is a wall mounted tap called?

Usually a wall mixer, or a wall spout and mixer when the spout is separate. Ours are the Milano wall mixer and the Milano wall spout and mixer.

What are the disadvantages of wall-mounted taps?

The body has to go into the wall before it is lined and tiled, so they suit a renovation or new build more than a quick swap. A bench-mounted basin tap fits one Ø35–38 mm hole and is easier to change later.

Which basin tap suits my basin?

Measure from the basin rim: the Vienna Tall leaves 200 mm under the spout, the Vienna Short 75 mm, and you want at least 50 mm of gap. Which tap fits my basin? does the maths.

Can I install a basin tap myself?

No. A licensed plumber installs it to the NZ Building Code (G12), and that is a condition of the warranty.

Can I change the finish later?

On the wall models, usually yes: the in-wall body is the same for all six finishes of a model, so it is a trim change rather than a new rough-in.

Bathroom mixer or wall tap: four ways to run a basin

Picking a basin tap, bathroom layout comes first: is the basin set into the bench, sitting on top of it, or does the tap go on the wall? We make one answer for each, in six finishes, and all four are certified under the Lead Free WaterMark scheme, which meets the NZ Building Code lead limit.

On the bench: Vienna Short and Vienna Tall

Leave at least 50 mm between the basin rim and the underside of the spout. The Vienna Short gives 75 mm, so it suits a basin in the bench or only slightly raised; the Vienna Tall gives 200 mm and suits a vessel basin with a rim up to about 150 mm. They reach 140 and 180 mm, and both fit a Ø35–38 mm hole. If you're replacing an old basin tap, the hole size usually decides it, so measure it before you choose a height.

Bathroom taps, wall mounted

A wall tap keeps the vanity top clear and works with a basin that has no tap hole. The Milano wall mixer controls the water from a Ø65 mm plate with a 115 mm lever; the Milano wall spout and mixer adds a basin spout that projects 192 mm. Both bodies need 45 to 70 mm of depth inside the wall, so they go in before the wall is lined.

Planning the rough-in

Because the body sits in the wall, your plumber fixes its position at rough-in, and the spout should clear the basin rim by the same 50 mm. Bathroom heights and rough-in measurements has typical figures, and wall-mounted vs basin mixer taps compares the two approaches. The in-wall body is shared across the six finishes of each wall model, so changing finish later is a trim swap (changing finish without retiling).

What's inside

DZR brass bodies, Citec ceramic cartridges, a 50 to 800 kPa working range and WaterMark licence WM-022467. We supply replacement cartridges if one wears. A matching pop-up waste or bottle trap finishes the basin.

Every product here has the same cover: 15 years on the body, 7 years on cartridges, valves and moving parts, 3 years on the finish and 2 years on washers, seals and O-rings (tapware warranty). Taps and showers must be installed by a licensed plumber, to the NZ Building Code (G12), for the warranty to apply.